Sliding Table Saw

How to Operate Sliding Table Saw Machine

Sliding Table Saws

This machine tool can cut and process all kinds of solid wood panels, wood-based panels, ABS panels, PVC panels, organic glass and other wood structures, and panels with similar hardness. It is one of the necessary equipment for the production of furniture, decoration and other industries.

Sliding panel saw machine is composed of a bed, a mobile worktable, a mobile worktable attached support, a fixed worktable, a main saw, a secondary saw, a transmission lifting mechanism, and a horizontal and vertical guide plate.

The machine tool guide rail is made of aluminum alloy linear guide rail, which is oxidized and has super high wear resistance and no deformation. To ensure that the machine tool can work accurately for a long time, the inclination angle of the main saw blade and the auxiliary saw blade is visually displayed by the precision angle meter, and the operation is very convenient.

1.Positioning plate    2.Bracket            3.Boom support rod

4.staff gauge         5.Auxiliary support    6.Workbench

7.Main saw blade     8.Auxiliary saw blade

9.Hand saw blade adjustment wheel

10.Backing          11.Control button

12.Enlarge the countertop

13.Auxiliary countertop

Sliding Table Saw

  1. This machine tool can provide vertical and horizontal sawing of square lumber and panels, and is suitable for processing various panels such as construction, furniture, vehicle and ship manufacturing.
  2. Features: This machine can saw wood, veneer particleboard, various man-made boards, plastic boards, and aluminum alloy boards. There are two saw blades at the front and back. The front is the pre-cutting saw and the back is the main saw. The two saw blades work at the same time, no planing process after sawing, good smoothness, high accuracy, and no burrs.
  3. The body has a sliding table and a fixed table. Therefore, the machine can be used for sawing and cutting the sheet size without laying a foundation.

2.Sliding Table Saw  Technical Parameter

Maximum cutting length2800/3000/3200mm
Maximum cutting width1250mm
Main saw blade diameter250-300mm
Vice saw blade diameter120mm
Main saw blade speed4500-6000rpm
Vice saw blade speed8000rpm
Main saw motor power4kw
Vice saw motor power0.75kw
Machine size3050*3150*900mm

Panel Saw Cutting Machine

3.Sliding Table Saw Composition and working principle

  1. The composition of the machine tool: The machine tool is composed of a sliding table part, a fixed table part, a cutting part, and an electrical part.
  2. 2.Motion system diagram

Working principle: After the adjustment of the machine tool is completed, according to the required plate size, align the backing plate according to the standard size on the worktable. The backing plate can be adjusted horizontally and diagonally. Adjust the main saw blade to an appropriate height (the pre-cutting saw lifting is controlled by the star handle) and then put the plate on the worktable and press the button to realize the cutting.

4.Handling, installation, adjustment and trial operation of machine tools

4.1 Handling: When handling the machine tool, avoid shock and vibration. When lifting, pay attention to whether the packaging is tightly bound and whether the lifting point is on the center of gravity of the machine tool. When tilting and rolling, the inclination of the board should not exceed 15°. The diameter of the roller shall not be greater than 60mm. The machine tool should be firmly tied with steel wire rope or hemp rope during lifting. The rope should not be in contact with the protruding part of the machine tool and the exposed processing surface after being tensioned. It must be protected by a replacement or thick paper liner to prevent damage. Paint and finish the surface.

4.2. Installation: The machine does not need to lay the foundation, it can be used after fixing the position.


6.3.1Adjustment of the sliding table relative to the saw blade

In order to avoid the second cutting of the teeth when the tool is raised, a free cutting area should be left, that is, the sliding table should not be completely parallel to the saw blade, and the difference in parallelism is 1 meter behind the blade For the maximum 0.1m, for the same reason, the pre-cut saw blade should also have a very small free cutting area.

In order to check the free cutting area, clamp a wooden board on the sliding table. After cutting, stopping and pulling back, it is found that the friction between the wooden board and the saw blade is very small, but the friction is large during sawing, indicating that the machine has been adjusted well. If there is no friction when it is pulled back, but there is strong friction when sawing, it means that the free cutting area is large.

Adjustment method:

(1)Loosen the two bolts connecting the slide seat and the bed

(2)Adjust the parallelism with two locknuts that clamp the workbench bolts on the side, (the sliding workbench and the fixed workbench have a certain gap) tighten the vertical screws.

4.3.2 Adjustment of the guide device on the fixed worktable relative to the saw blade

The left side of the saw blade should have the same parallelism difference. In order to check the adjustment, install the largest saw blade and correct the side elevation by using the parallel guide device. If the guide device is adjusted well, it depends on the free cutting in the diameter direction of the saw blade. , Use a 1-meter-long software to cut freely, and the test piece should not exceed 0.15mm.

Adjustment method:

(1)Loosen the outer nut of the two bolts holding the rod

(2)Adjust and tighten 2 lock nuts

(3)Fix it on the machine body with a nut.

4.3.3 Vertical angle cutting adjustment

The horizontal backing board of the sliding table is used for sawing the vertical angle. To adjust it correctly, take a piece of wood and cut 2 vertical planes. Use a square or feeler ruler to measure the length of 0.24mm at 500mm.

Adjustment method:

(1)Loosen the handle under the outer end of the lateral baffle

(2)Rotate the black star handle on the side

(3)When the school team is qualified, tighten all bolts.

4.3.4 Height adjustment of sliding table relative to fixed table

The sliding workbench is 0.3mm higher than the fixed workbench to avoid mutual friction when pushing the wood. If there is an abnormal situation, the fixed workbench should be adjusted and adjusted by the four corner support bolts of the distributed workbench.

Adjustment method:

  • Lift the workbench: loosen the lower nut and tighten the

upper nut

(2)Workbench down: loosen the upper nut

(3)Check and adjust the parallel guide mechanism.

4.3.5Adjustment of the stability of the sliding table

Nylon rollers are installed on both sides of the slide, and the cylindrical surface of the roller rolls on the bottom plane of the slide seat to prevent possible swing and bumps during the movement of the movable table to make it stable. Roll along the guide to ensure the normal cutting of the machine tool. Stability and accuracy.

4.3.6.Parallel adjustment of the main saw blade and the auxiliary saw blade

The secondary saw blade is not parallel to the main saw blade, and there will be burrs or steps on the cutting surface of the sawing veneer board, so adjust it. Twist the auxiliary saw by hand to support the outer hexagon of the front side, so that the auxiliary saw can be moved inward or outward to be parallel to the main saw blade.

Share this post

Leave a Reply